Replacing uPVC Window Handles
It is simple to change the handles on upvc windows. It is important to make sure that the new handle is fitted into the spindle cutouts in the window mechanism.
If you follow the steps below the handle of any cockspur will fit on most windows. The most important factor is the step size of the handle.
What to Find
A large portion of windows in the UK are fitted with uPVC handles Over time, they may begin to show signs of wear and tear. When this occurs, the window handle can become loose or difficult to operate, which makes it necessary to replace it. Anyone who is familiar with basic hand tools is able to complete this job.
The first step is to ensure that the handle is securely fixed to the frame of the window and in its open position. The next step is to find the fixing pins or screws that keep the handle in the position it is in. These are typically located on the inside of the handle and can be removed with a screwdriver, or pliers.
When the handle is loose, it can be removed from its hinges by gently pulling it off. It is then time to find a new handle that is the same design and size. This can be done on the internet or at an area DIY store, and should take about five minutes with a screwdriver.
The most important thing to consider when replacing a uPVC window handle is its step height. This is the distance from the base of the handle until it rests on the frame of the window. This is usually a standard measurement, and it is important to check the step height of your existing handle prior to ordering a new one.
Depending on the type of handle you have, there are different sizes that are available. Inline handles can be found for uPVC window with lug centres of 31mm while cockspur handles come with centers of lugs of 43mm. Tilt-and turn handles are typically found on uPVC windows. They have a special design that allows the window to be slid down to let in air, and then turned to fully open the window.
The most common uPVC handle cracks are internal, rather than a breakage from the base. This can make them hard to open and therefore it is crucial to ensure that the replacement handle you buy has the same length of spindle as the one you have.
Remove the Old Handle
A poorly installed or damaged window handles can cause your double-glazed windows to open and close incorrectly, and can result in them getting stuck. window handles www.repairmywindowsanddoors.co.uk can be caused by various factors, such as general wear and tear on the metal handle or corrosion. In these situations it is essential to replace the window handle as promptly as you can to avoid further damage or loss of function.
When replacing upvc windows handles it is recommended to remove the handles that were previously installed from the window. Start by removing the screw covered by the handle while it is in the closed position. This will reveal a screw, and once it is removed, you can begin to remove the handle itself. It is a good idea to make use of an electric screwdriver for this since it will make the task much easier and quicker.
It is also worth noting that the screws on the handle may be hidden behind plastic caps, therefore it is recommended to take a Stanley knife to the screw caps and then remove them. After removing the handle, you will be required to inspect the square cutout on the base to ensure that the new handle you choose for the window lock is compatible. It is important to measure the length of the spindle on the old handle and then compare it with the dimensions of the window mechanism spindle cutout.
The different types of window handles made of upvc are: Espag handles, which have a central screw and can turn left or right; Cranked handles, which have two screws and are used on tilt and turn upvc windows and Spade handles which have an arm with a flat surface and can be used on either side of the window. It is simple to replace the handle after you've located one that is suitable. Simply put it in place and ensure that the spindle is properly inserted into the lock mechanism. After that, you can you can tighten the handle onto the window frame. The new upvc handles should now be secure.
Take a measurement of the Spindle
If you have to replace a Upvc handle that has fallen, it's likely that the spindle holding it in place is damaged or loose. In some instances, it can be fixed by using screws or pins to tighten it. In other cases it will require replacement completely. There are a variety of handles made from upvc. There are three kinds of handles: inline espagnolette, tilt-and-turn, and cockspur. Each type of handle is mounted and replaced in a different manner.
Before you purchase a new handle, it is important to know the dimensions of the existing one. This will ensure that the handle fits the window properly and will be of the correct size. All handles are calibrated in accordance with industry standards, making it easy to determine the right size.
To measure the handle's size, turn the window to the open position. You will then be able to determine the size of the screw or pin that holds it. Make use of a ruler or tape measure to determine how long the spindle is. Once you have determined the length of the spindle, you can purchase a replacement one that is exactly the same size.
The step height of a window handle is another factor to take into consideration when you are buying replacements. The step height is measured from the base to the point where the handle is positioned on the frame. Typically, this will be around 21mm for uPVC windows or 9mm for aluminium. Dropping something in the gap will let you see how far the handle extends before it comes into contact with an obstruction.
Cockspur handles come with different backsets depending on what type of window you put them in. Inline Espag handle heights are 43mm from centre to centre (two fixing points). Cockspur handles, however have different backset heights dependent on the design of the window they're in. This is because they have a spur which extends from the handle and locks onto a cockspur wedge-striking plate.
Install the new handle
After you've chosen the new handle, make sure it is aligned with the holes for screws on the door. Secure it using the screws provided. Install the latch lever in similar fashion to the handle that you are replacing in the event that you are replacing the door handle. Then, you can attach the door trim to conceal the mounting screws.
Tips: To remove a metal head from a wooden wedge, place the handle on the floor so that its wide end is on the ground. Then, you can use an hammer and tap the thin end. Be careful not damage the handle or handle spindle.